Do you have an old metal bed frame that’s seen better days? You can give it new life with a bit of effort and elbow grease! Taking apart a bed frame metal doesn’t have to be overwhelming, especially if you know how to do it safely and efficiently.
All the tools and materials that you require can be easily gathered from your local hardware store. So roll up your sleeves and get ready to get workplace ready—we are about to show you how to take apart bed frame metal like a true DIY master!
Needed Tools and Materials
Given below is the list of tools and materials that you will need before getting started:
- Hammer
- Phillips Screwdriver
- Flat Head Screwdriver
- Wrench
- Pliers
- Ratchet Set
- Spare Screws (of the Same Size as the Originals)
- Safety Glasses
Step-by-step Guidelines on How to Take Apart Bed Frame Metal
Step 1: Prepare the Bed Frame
Before you begin taking apart the bed frame, it is important to lay the furniture on its side so that all bolts and screws can be easily accessed. Make sure that the bed frame is stable when laying it down.
It is best to do this on a soft surface such as a rug or carpet to avoid scratching it. You may also want to use a piece of cloth or foam between the bed frame and the rug. This will help protect the bed frame from any unwanted scratches.
Step 2: Unscrew Bolts and Nuts
Now, or bolts that are attached to the bed frame. Most metal bed frames have two or more connection points, which will require you to unscrew them. It is essential that you pay attention to the order in which you unscrew them.
This will help avoid any confusion when it comes time to reassemble the bed frame. You may also want to take a picture of the frame before you start taking it apart, as this will make reassembly easier.
Step 3: Unscrew Screws
The next step is to use a Phillips screwdriver or a flathead screwdriver to remove any screws from the bed frame. Make note of where each bolt and screw is placed so you can easily re-attach them later on.
Otherwise, you may end up with a jumbled mess of screws and bolts. It is also important to take note of any washers or nuts attached to the screws and bolts.
Step 4: Disconnect the Slats from the Bed Frame
Now it’s time to remove any slats that are connected to the bed frame. The slats should be secured with screws, which can easily be unscrewed using a Phillips or flathead screwdriver.
But be careful not to pull too hard as this could damage the slats. It’s also important to note the order in which you removed the slats, as this will be necessary for re-assembling.
Step 5: Unscrew Any Nails
If there are any nails that require unscrewing, use a hammer to gently pull out the heads of the nails so you can safely remove them from the bed frame. Take care to not damage any parts of the bed frame while doing this. You may also need to use a plier to bend the metal nails back in place if they are too tight.
Step 6: Remove the Old Paint
If your bed frame is covered in paint, use a hammer and pliers to carefully chip away at it. This will make it easier to remove the rust from any metal parts and refinish them with a fresh coat of paint if desired. This step is optional but is recommended if you want to give your bed frame a fresh, new look.
Step 7: Unscrew Any Remaining Bolts
Once all the nuts, bolts and screws have been removed, use a wrench to unscrew any remaining bolts from the bed frame. Make sure that you take note of where each bolt and nut is placed so that you can re-attach them correctly later on. But be careful not to over-tighten the bolts as this could damage the bed frame. Although this step is optional, it can help make reassembly easier.
Step 8: Separate the Bed Frame Pieces
Now it’s time to separate the bed frame pieces from one another. This is done by carefully pulling apart the two sides of the frame using your hands and a hammer if necessary. Be careful not to scratch or damage any parts while doing this.
This step is important for reassembly and should be done carefully. It is also recommended to take pictures of the bed frame before and after taking it apart to make reassembly easier.
Step 9: Clean and Sand
Once all the pieces have been separated, use a wire brush to clean off any dirt, grime and rust that may have accumulated on the metal frame. After cleaning, use sandpaper to smooth out any rough edges or irregularities in the surface of the bed frame. But be sure to wear safety glasses while sanding to protect your eyes from any flying dust particles.
Step 10: Reassemble the Bed Frame
Once you’ve finished cleaning and sanding, it’s time to reassemble the bed frame. Start by placing the two sides of the frame back together and reconnecting them using screws, bolts and nuts.
Make sure that all connections are secure before proceeding to the next step. It is important to also take note of where each bolt and screw is placed if you want to avoid confusion during reassembly.
Step 11: Refinish or Paint
The last step is to refinish or paint your bed frame if desired. You can either choose a new color for your frame or opt to keep it as is. If you do decide to paint the bed frame, make sure that you use a high-quality primer and paint to ensure better coverage and a longer-lasting finish. Always read and follow the instructions provided on the primer and paint before applying.
Following these steps on how to take apart bed frame metal and taking the necessary safety precautions will help you successfully take apart bed frame metal. With just a bit of effort and time, you can make your old metal bed frame look as good as new!
Do You Need to Use Professionals?
Although it is possible to take apart bed frame metal yourself, it is also recommended to seek the help of professionals if you are not familiar with taking apart furniture. Professionals will be able to safely and quickly take apart your bed frame without causing any damage or injury.
It is essential that you choose a reputable professional who has experience in dismantling furniture and can provide quality workmanship. Professional services may cost a bit more than doing it yourself but will ultimately save you time and effort in the long run.
Frequently Asked Questions
Q: What Tools Do I Need to Take Apart a Bed Frame Metal?
A: You will need a hammer, Phillips screwdriver, flat head screwdriver, wrench, pliers, ratchet set and safety glasses. It is also helpful to have spare screws of the same size as the originals.
Q: How Do I Refinish or Paint a Metal Bed Frame?
A: If you want to give your bed frame a new look, start by removing any old paint from the surface with a hammer and pliers. After cleaning and sanding, apply a high-quality primer and paint, making sure to let each layer dry before applying the next. This will ensure better coverage and a longer-lasting finish.
Q: What Safety Precautions Should I Take When Taking Apart Bed Frame Metal?
A: It is important to always wear safety glasses when working with metal bed frames as there may be pieces of metal that can fly off and injure your eyes. It is also wise to avoid using a hammer or pliers directly on the bed frame as this can damage the frame. Finally, make sure to take note of where each bolt and screw is placed so you can easily re-attach them later on.
Q: How Do I Store the Bed Frame Metal After Taking It Apart?
A: If you plan on keeping the bed frame parts for future use, it is important to store them in a dry and dust-free area. Make sure that all pieces are labeled so you can easily find them once you’re ready to reassemble the bed frame.
Conclusion
The task of disassembling a bed frame may seem daunting at first, but with the right tools, it’s not as difficult as you might expect. By following these steps and taking your time, you can have the metal bed frame apart in no time.
Once that’s done, you can use the salvaged parts for a new project or discard them. If nothing else, this process will give you a chance to hone your problem-solving and power tool skills.
Working with furniture is all about breaking it down into manageable tasks. So why not take advantage of this opportunity? Give yourself some breathing room by finding those screws and bolts that need to be taken apart and start disassembling that bed frame today! Thanks for reading this article on how to take apart bed frame metal.
