How to Remove Gas Lift From Office Chair

Removing the gas lift from an office chair is important before replacing it with a new one or making any other repairs. It’s also essential to ensure that your chair is properly secured and functioning safely. This process can be intimidating if you’re unfamiliar with disassembling furniture, but it’s quite simple.

How to Remove Gas Lift From Office Chair

The main advantage of removing a gas lift from an office chair is that it can make the chair more comfortable and easier to adjust. Gas lifts are often used to raise or lower the seat height of an office chair, but they can also be difficult to adjust and may cause discomfort when sitting on them for extended periods of time. Removing the gas lift from an office chair can make the seating experience much more pleasant. In this blog post, You will learn in detail how to remove gas lift from office chair.

Tools You Will Need

  • Phillips Head Screwdriver
  • Flathead Screwdriver
  • Socket wrench and socket set
  • Pliers
  • Ratchet and Ratchet Extension
  • Wrench Set
  • Measuring Tape or Ruler
  • Safety Goggles or Glasses
  • Adjustable Wrench
  • Pieces of Wood (optional)

Step-by-Step Processes for How to Remove Gas Lift From Office Chair

Step 1: Inspect the Chair Base

Look for the gas lift on the chair base. It should be located in the center of the chair and is likely to be covered by a plastic cap or metal sleeve. If you do not see it, check underneath the chair and look around the edges.

Step 2: Remove the Gas Lift Cover

Use a flat-head screwdriver to remove the cap or sleeve covering the gas lift carefully. Be sure to be gentle, as excessive pressure may damage the chair. Grip the gas lift base with one hand and pull it straight up. The gas lift will come out of its socket in one motion. Set aside for disposal or reuse.

Use a Flat-head Screwdriver

Step 3: Clean Gas Lift Socket

Use a cloth to wipe away any dust or debris in the gas lift socket. Be sure it is clean and free of any obstructions. Insert the new gas lift into its socket. Push down firmly until you hear a clicking sound indicating it is securely in place.

Step 4: Re-attach Gas Lift Cover

Place the cap or sleeve back over the top of the gas lift and use a flat-head screwdriver to re-attach it to the chair base. Re-attach the chair base to the seat. Make sure all screws and bolts are securely tightened.

Step 5: Check the Stability of the Chair

Rock back and forth when sitting in the chair to check if it is stable and secure. If not, repeat the steps until it is. Depending on the model of your chair, you may be able to adjust the height of the gas lift with a knob or lever. Check the instructions manual to determine how to do this, if necessary.

Sit back in your chair and enjoy the comfort and convenience of your gas lift office chair. By following these steps, you can easily remove and install a gas lift on your office chair. With minimal effort and time, you can ensure your chair is safe and comfortable to use daily.

Sitting in the Chair to Check

Importance of How to Remove Gas Lift From Office Chair

  • Safety: Removing the gas lift from an office chair can help prevent accidents and injuries that may result from malfunctioning or faulty components. A broken gas lift can lead to the chair tipping over unexpectedly, causing harm to the user. By taking out the gas lift before it becomes a problem, you can ensure the safety of your staff.
  • Comfort: An office chair with a broken gas lift can be an uncomfortable place to sit, as it cannot adjust properly and maintain proper support. Removing the gas lift helps ensure you provide a comfortable and supportive workspace for your staff.
  • Durability: Gas lift components are designed to last, but they can become damaged over time and need to be replaced. By removing the gas lift from an office chair that is no longer functioning properly, you can help ensure its long-term durability.
  • Cost Savings: Replacing a broken or worn-out gas lift can be costly, so removing the gas lift and replacing the entire piece is much more cost-effective than buying a new lift.
  • Ergonomics: By removing the gas lift, you can improve the ergonomic design of your office chair. This helps ensure that your employees have a comfortable work experience, which can help increase productivity and reduce fatigue.
  • Aesthetics: An office chair with a broken or worn-out gas lift can be unsightly, detracting from the overall look of your workspace. Taking out the gas lift helps to ensure that your office has an aesthetically pleasing appearance.
  • Easy Maintenance: Removing the gas lift from an office chair makes it easier to take care of, as you can easily inspect and clean its components.
  • Weight Reduction: A broken or worn-out gas lift can add unnecessary weight to your office chair, making it harder to move around. Removing this component helps reduce the overall weight of the chair, making it easier to transport and maneuver.
Removing the Gas Lift

Overall, removing a gas lift from an office chair can help to improve the safety, comfort, durability, cost savings, ergonomics, aesthetics, maintenance and weight reduction of the piece.

Safety Tips for How to Remove Gas Lift From Office Chair

  1. Make sure to turn off the gas lift mechanism completely before attempting to remove it from your office chair.
  2. Remove any screws or other fasteners that are holding the gas lift in place using a screwdriver or other appropriate tool.
  3. Place a piece of cloth beneath the gas lift and use another piece to cover the gas lift to protect your hands from being burned.
  4. Using two wrenches, one on each side, carefully unscrew and remove the gas lift from its mounting points.
  5. If possible, wear safety glasses when handling and removing the gas lift as some of the metal parts can be sharp or have burrs that could damage your eyes.
  6. Check the condition of the gas lift before re-installing it. If there are any signs of wear or damage, consider replacing it with a new one.
  7. Make sure you have all the necessary tools and parts for reinstalling the gas lift before you begin so that everything goes smoothly when assembling it again.
Remove Any Screws or Other Fasteners

By following these safety tips, you can safely remove a gas lift from your office chair.

Is There Any Specific Technique That Should Be Used When Removing the Gas Lift? 

Yes, a few steps need to be followed when removing the gas lift from an office chair. Before attempting any repair work, always unplug the chair from its source to ensure safety and prevent shock.

First, remove the seat cushion from the base by unscrewing the screws on the seat’s underside. Then, locate the gas lift and unscrew it from its housing at the bottom of the chair. Unscrew the plastic cover to expose two metal plates holding the gas cylinder.

Using a flathead screwdriver, carefully pry off one plate and slide out the gas cylinder. Be sure to take note of the orientation of the cylinder and its parts before removing it. After that, remove the metal plate from the other end of the gas lift. Finally, take out the plastic cover completely and twist off the spring-loaded pin on top of the gas lift. 

Once all these steps are complete, you can now safely remove the gas lift from your office chair. It is important to note that the exact steps for removing the gas lift may vary depending on the make and model of your office. Therefore, it is best to refer to the manufacturer’s instructions before attempting any type of repair work.

Are There Any Other Issues You Should Be Aware of That Could Cause the Gas Lift to Malfunction? 

A few potentials could cause the gas lift in your office to malfunction. This includes issues with the gas lift’s mechanism itself (i.e., worn or broken parts) and external factors such as the alignment of the seat base and other furniture pieces in relation to the chair. If you find that the gas lift is not functioning properly, inspecting the mechanism for any visible signs of damage may be advisable.

Additionally, ensure that other furniture pieces in the vicinity are not blocking or interfering with the gas lift’s ability to move. If you suspect any external factors are contributing to your problem, it would be best to consult a professional for assistance.

Finally, disconnect the gas lift from the seat base and remove it completely. Be aware of potential issues that could cause a malfunction in your office chair’s gas lift, and consult a professional if you suspect any external factors may be contributing to this problem.

Disconnect the Gas Lift From the Seat Base

Is There Any Maintenance That Needs to Be Done on the Chair Once the Gas Lift Has Been Removed? 

Yes, once the gas lift has been removed from your office chair, you should take a few maintenance steps. It is important to clean and lubricate the parts of the chair where the gas lift used to be. This will help prevent any debris or rust from building up and make sure that your chair remains in optimal condition. 

You may also want to check the rest of the components on your chair for any signs of wear and tear. This will help you replace any worn or malfunctioning parts before they cause an issue with the overall function of your chair. Finally, ensure that all the screws and fasteners are tightened properly to keep everything secure. 

Taking these few simple steps will help keep your chair in good condition for years to come. However, it is important to remember to clean and lubricate the parts where the gas lift used to be and check for signs of wear and tear on the rest of the chair components. Doing this will help ensure that your office chair remains in optimal condition and that all its parts function correctly.

Are There Any Common Mistakes People Make When Attempting to Remove a Gas Lift From an Office Chair? 

Yes. One of the most common mistakes people make when attempting to remove a gas lift from an office chair is not using the correct tools for the job. A flat-head screwdriver can cause damage to both the gas lift and the chair, leading to costly repairs or replacements. 

It’s also important to follow any directions provided with your chair when attempting to remove a gas lift. If instructions are not included, always take caution and use the correct tools for the job. Additionally, be sure never to force or overextend the gas lift, which can cause breakage and serious injury. Lastly, it’s important to know that some office chairs have a locking mechanism that must be disengaged before attempting to remove the gas lift. 

Use the Correct Tools

If this is not done, you may be unable to remove the gas lift successfully. If you are still unsure how to remove a gas lift from your office chair properly, it’s best to consult a professional technician for help. A trained technician will be able to safely and accurately remove the gas lift in a timely manner. Taking these steps can ensure that your office chair remains in top working condition and is safe for use.


In conclusion, removing a gas lift from an office chair is not as difficult or intimidating of a task as many may think. With the right tools and patience, anyone can successfully remove the gas lift quickly. It’s important to note that it’s best practice to wear safety glasses when attempting any repair job, especially one involving sharp objects like pliers. 

In addition, be sure to carefully inspect the gas lift before attempting any repairs or replacements, as it can be dangerous if not done properly. I hope this article has been beneficial in learning how to remove gas lift from office chair. Make Sure the precautionary measures are followed chronologically. 

Photo of author

Adrian Green

Adrian is a woodworking hobbyist and has loved Woodworking since he was 10 years old. Back then in childhood, his father used to have a furniture shop. He used to help his dad and learned a lot from him about how to fix woodworking furniture, basic carpentry knowledge and also about how to work hard and take care of business. He enjoys woodworking as a hobby. He loves the feeling of creating something with his own hands, and the satisfaction that comes from seeing his finished products used by others.

Leave a Comment